Customer Service
Customer Service

Jack & Jill Bathroom Locking System

5 7

No Interruptions

No unwanted interruptions.

Shared Jack & Jill bathrooms are an effective way to provide en-suite facilities to two rooms without having two separate bathrooms.  But it can cause a rift in the household when doors are left locked on one side when unoccupied - or indeed accidentally left unlocked when occupied!  This can cause obvious problems - either you're unexpectedly walked in on - or you're waiting to use the bathroom after finding the door is locked when in fact nobody is even in there!

This is where our automated electronic Jack & Jill solution works perfectly, allowing you to simultaneously lock both doors in one simple action when using the bathroom, and then unlocking both doors before leaving.  This way, no doors are accidentally left locked or unlocked when they shouldn't be!

Sit Back and Relax

Sit back and relax.

Our solution takes care of everything.  By use of a simple pull-chord just like your bathroom light switch, you can lock both doors at once, giving you peace of mind that both doors are now locked.  When you want to leave, pulling the switch again will unlock both doors, allowing you to leave without having to remember to cross the room and un-lock the other door to allow the shared bathroom to be used from the other side.

One less thing to worry about

That's one less thing to worry about.

In bathroom environments, safety is key.  And we've made sure this setup keeps you and your family safe.  There is no mains wiring involved.   You would host an enclosed power supply unit inside a cupboard or similar outside of the bathroom, which would plug into a standard plug socket.   From here, everything is no more than 12volts.  This ultra-low voltage means there's no risk of extreme hazard like there could be with mains wiring.  Everything used is low-voltage and low-power, so no hefty bills either!

Similarly, because the power supply unit is to be simply plugged into a standard plug socket, this means you can gain entry in the event of an emergency simply by switching the system off at the wall or unplugging it!

How does the Jack & Jill Bathroom Locking System work?

The way our system works is that on each door, you would fit the supplied latches to work in conjunction with the supplied electronic door releases.  These would be fitted in conjunction with your existing latches and handles, so the handle operation to the end-user never changes (although if you have physical locks on these doors, you may want to change these or replace the handles with blank backplates so that no physical locking function is available).  

The electronic door releases will be inactive - allowing the door to be opened freely as normal - until the pull chord is pulled to change the releases to the 'locked' state.  If the pull-switch is pulled while one of the doors is still open, this is not a problem - because the use of latches means the doors can still be closed while the electric releases are engaged (locked), just not opened (until the switch is pulled again to disengage them).  It is important to know that as with any other latching locks there will ultimately be noise generated by the door when pushing or pulling the door closed. 

The pull switch would usually be located in a universal location rather than right by the door - so that it is convenient for everyone to use.  However you can utilise multiple switches of any suitable kind if preferred.

What's included in the Jack & Jill Bathroom Locking System?

The kit we have put together is based on the countless systems we have built based on customer requirements, and this is the most common general setup we have successfully quoted for over the years.   The bundle includes:

  • A regulated boxed power supply unit
  • An installation wiring kit, containing 20m of 6-core cable, 2 metres of 3 core flex cable, a 20mm stuffing gland, 60 cable clips and a fused plug-top
  • Two flat latches (one for each door)
  • Two electronic door releases (one for each door)
  • The ceiling pull-switch to lock / unlock
  • If you have specific requirements or feel this system may not be quite right for you, let us know!  We are happy to put together an altered package just for you, it's all part of what we do every day!

Important: This kit requires wiring and is for Professional Install Only!   It is also advised to consider instructional signage to ensure that all visitors can operate the system effectively and safely.  

What Existing Users Are Saying

Purchase Options

Product Name Price Tap in Qty
Jack & Jill Bathroom Lock Kit
£170.75 + VAT
£144.49 + VAT
(£173.39 inc VAT)

Our product specifications are given in good faith but can be subject to manufacturer change without notice. Should an attribute be of essense to your purchase, please feel free to contact us first for confirmation.

Questions & Answers

Ask a question about this product

** Please ensure you have checked the product description and previous Q&A's to see if your question has already been answered! **

The LocksOnline Team


Head of the tech team, and locksmith of 25+ years


Specialises in Ironmongery & Door Furnishing


Deals with Sales on the website


Deals with Sales on the .com website


Ensures day-to-day logistics run smoothly


Keeps our workshop running smoothly


Our web developer and content manager

Close the chat box

We will phone you - Request a call back